E-Flo iQ Software Change History

The Version History of the E-Flo iQ Software is listed below. The software currently installed on an E-Flo iQ system can be found by navigating to Advanced Setup Screen four. Details on this screen can be found in E-Flo iQ Operation Manual 333587.
All E-Flo iQ systems should match one of the following system versions.If an upgrade to a newer software version is desired, follow the procedure in manual 3A6321 to download the latest version of software to a token.  Alternatively, order the appropriate “Software Upgrade Token” as listed below. This Upgrade Token is used to upgrade software on all of the system components per the procedure described in manual 3A1244.

NOTE: Upgrading software may clear some USB data (i.e. pump cycles, material volume, etc.)  It is recommended that a full USB download be completed before upgrading software.

Important!

  • If upgrading from a revision older then 2.03.007, then it is recommend that a picture is taken of the desired style definition and heat settings. As the token upgrade, will delete and reset the style definitions and heat settings. Once the upgrade is completed, the data will need to be re-entered into the ADM.
  • If upgrading from 2.03.007 or newer, then the upgrade token will not delete and reset style definitions or heat settings and all data will be saved during the token upgrade.

DOWNLOAD LATEST SOFTWARE HERE:

Software Upgrade Token 18A921 Series S

  • System: 18A920s.gti (Software Link) version 2.05.001
  • Advanced Display (ADM): 18A900 version 2.04.011
  • USB Configuration: 18A903 version 2.01.001
  • Motor Control Module (MCM): version 2.04.003
  • Auto Mult-Zone (AMZ): version 1.03.007
  • I/O Daughter Board (DB): version 2.03.011
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Fixed issues with Motor Control Module’s CPU & system network communications
  • Fixed issues with the priming targets not showing up on ADM
  • Pressure sensor offsets changed to correct the incorrect pressure readings.
  • Pressure limit set to alarm at 7000psi instead of 7500psi.

Software Upgrade Token 18A921 Series R

  • System: 18A920 version 2.04.005
  • Advanced Display (ADM): 18A900 version 2.04.006
  • USB Configuration: 18A903 version 2.01.001
  • Motor Control Module (MCM): version 2.03.007
  • Auto Mult-Zone (AMZ): version 1.03.007
  • I/O Daughter Board (DB): version 2.03.007
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Fixed issues with the heat on startup
  • Visual enhancements on the start/stop button
  • Relinquishing control of the iQ from the fieldbus, does not turn off heat

Software Upgrade Token 18A921 Series P.

This is a major revision please download and review this software buletin for the required step to successfully upgrade your E-Flo iQ. 

E-flo iQ Software Upgrade Bulletin 05October2021.pdf

  • System: 18A920 version 2.03.007
  • Advanced Display (ADM): 18A900 version 2.04.002
  • USB Configuration: 18A903 version 2.01.001
  • Motor Control Module (MCM): version 2.03.007
  • Auto Mult-Zone (AMZ): version 1.03.007
  • I/O Daughter Board (DB): version 2.02.003
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • IMPORTANT: This token will delete and reset the heat and style definition information, it is recommended to take a picture of desired information before updating, as the information will need to be re-entered after updating is completed.
  • IMPORTANT: This token will reset the USB log; therefore complete a USB download to keep the data.
  • Added tenths to the heat data exchange temperature elements.
  • Added multi-level password protection.
  • Change the temperature offsets from a global parameter to a zone parameter. So that temperature offsets can be set differently on each zone.
  • Fixed bug where the unit of ⁰F was not working correctly on the temperature offset screen
  • Fixed bug where there was a rounding error when globalizing heat temperature variables.
  • Added the style delays control to the maps.
  • Added flow rate, pre-charge and delay commands to pump data exchange.
  • Added fieldbus request of styles 0-999, however if the style is over 16, then the information must come from the fieldbus.
  • Added heat status to the pump system ready status. the pump system ready will remain low if the heat is not up to temperature
  • Created two new maps (18E217 - Ambient & 18E223 - Heated) and obsoleted maps (18A909 - Ambient & 18A915 - Heated)
  • Added the capability for E-Flo iQ to run as a E-Flo SP Warm Melt.
  • Fixed issues with the displaying of Job Logs.
  • Fixed issue with heat alarms and deviations not holding for temperature offsets.
  • Fixed issue where the unit would not display the correct flowrate at high flows.
  • Improved bead dispensing performance

Software Upgrade Token 18A921 Series N.

  • System: 18A920n version 1.03.002
  • Advanced Display (ADM): 18A900 version 1.03.005
  • USB Configuration: 18A903 version 1.03.003
  • Motor Control Module (MCM): version 1.05.003
  • Auto Mult-Zone (AMZ): version 1.03.005
  • I/O Daughter Board (DB): version 1.03.014
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • System enable now turns on pump and heat.

 

Software Upgrade Token 18A921 Series M.

  • System: 18A920m version 1.03.001
  • Advanced Display (ADM): 18A900 version 1.03.001
  • USB Configuration: 18A903 version 1.03.003
  • Motor Control Module (MCM): version 1.05.001
  • Auto Mult-Zone (AMZ): version 1.03.005
  • I/O Daughter Board (DB): version 1.03.014
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Added Valve and Motor On and Off Delays to Styles.

 

Software Upgrade Token 18A921 Series L.

  • System: 18A920L version 1.02.031
  • Advanced Display (ADM): 18A900 version 1.02.031
  • USB Configuration: 18A903 version 1.03.003
  • Motor Control Module (MCM): version 1.04.001
  • Auto Mult-Zone (AMZ): version 1.03.005
  • I/O Daughter Board (DB): version 1.03.014
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Removed Shot Mode.
  • Allow foot switch operation from ADM control.

Software Upgrade Token 18A921 Series k.

 

  • System: 18A920k version 1.02.029
  • Advanced Display (ADM): 18A900 version 1.02.024
  • USB Configuration: 18A903 version 1.03.003
  • Motor Control Module (MCM): version 1.03.001
  • Auto Mult-Zone (AMZ): version 1.03.004
  • I/O Daughter Board (DB): version 1.03.014
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Updated EEPROM chip size.
  • Fixed the line voltage display on the ADM and CGM.
  • Addressed heat problems.
  • Added a slow, fast and normal option for heating.

Software Upgrade Token 18A921 Series J.

 

  • System: 18A920 version 1.02.023
  • Advanced Display (ADM): 18A900 version 1.02.017
  • USB Configuration: 18A903 version 1.03.003
  • Motor Control Module (MCM): version 1.02.024
  • Auto Mult-Zone (AMZ): version 1.03.004
  • I/O Daughter Board (DB): version 1.03.001
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Address EEPROM chip size change.
  • Moved style information in EEPROM.
  • shot mode released.

Software Upgrade Token: 18A921 Series H.

  • System: 18A920 version 1.02.020
  • Advanced Display (ADM): 18A900 version 1.02.017
  • USB Configuration: 18A903 version 1.03.003
  • Motor Control Module (MCM): version 1.02.019
  • Auto Mult-Zone (AMZ): version 1.03.004
  • I/O Daughter Board (DB): version 1.03.001
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Addressed EEPROM chip size changed.
  • Addressed number of EEPROM writes in CGM control.
  • Addressed bugs found in the field.

Software Upgrade Token: 18A921 Series G.

 

  • System: 18A920 version 1.02.019
  • Advanced Display (ADM): 18A900 version 1.02.017
  • USB Configuration: 18A903 version 1.03.003
  • Motor Control Module (MCM): version 1.02.018
  • Auto Mult-Zone (AMZ): version 1.03.004
  • I/O Daughter Board (DB): version 1.03.001
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Fixed a condition where the valve would not report a high temperature alarm. 
  • Removed a nuisance high temperature advisory when an RTD is missing or unplugged.
  • Rolled in a change with the Cold Board to increase a motor overcurrent alarm from 3000 psi to 3800psi.

Software Upgrade Token 18A920 Series F.

  • System: 18A920f version 1.02.017
  • Advanced Display (ADM): 18A900 version 1.02.017
  • USB Configuration: 18A903 version 1.03.003
  • Motor Control Module (MCM): version 1.02.017
  • Auto Mult-Zone (AMZ): version 1.03.003
  • I/O Daughter Board (DB): version 1.02.015
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Fixed bugs and issues with Tandem iQ systems.

 

Software Upgrade Token 18A920 Series E.

  • System: 18A920e version 1.02.006
  • Advanced Display (ADM): 18A900 version 1.02.010
  • USB Configuration: 18A903 version 1.03.002
  • Motor Control Module (MCM): version 1.02.014
  • Auto Mult-Zone (AMZ): version 1.03.001
  • I/O Daughter Board (DB): version 1.02.012
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Release of iQ Tandem Systems.

Software Upgrade Token 18A921 Series D.

  • System: 18A920d version 1.01.008
  • Advanced Display (ADM): 18A900 version 1.01.002
  • USB Configuration: 18A903 version 1.01.001
  • Motor Control Module (MCM): version 1.01.009
  • Auto Mult-Zone (AMZ): version 1.02.009
  • I/O Daughter Board (DB): version 1.01.001
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Fixed a reset bug in the Thrust counting feature
  • Fixed the job log displaying random information
  • Fixed the pressure graph, missing dispense valve off data
  • Removed smart empty from the iQ.

        Will allow for a style to be completed. Once the style enable is removed, and the empty level sensor is reached, the system will display that the drum is empty. If a tandem system, the system will crossover to the inactive or standby system.

Software Upgrade Token: 18A921 Series C.

  • System: 18A920c version 1.01.004
  • Advanced Display (ADM): 18A900 version 1.01.001
  • USB Configuration: 18A903 version 1.01.001
  • Motor Control Module (MCM): version 1.01.006
  • Auto Mult-Zone (AMZ): version 1.02.009
  • I/O Daughter Board (DB): version 1.01.001
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Intial Release.