E-Flo UniDrum Software Change History

The Version History of the E-Flo UniDrum Software is listed below. The software currently installed on an E-Flo UniDrum system can be found by navigating to Advanced Setup Screen, page four. Details on this screen can be found in E-Flo UniDrum Operation Manual 3A8735.

All E-Flo UniDrum systems should match one of the following system versions.

If an upgrade to a newer software version is desired, follow the procedure in manual 3A6321 to download the latest version of software to a token.  Alternatively, order the appropriate “Software Upgrade Token” as listed below. This Upgrade Token is used to upgrade software on all of the system components per the procedure described in manual 3A1244.

NOTE: Upgrading software may clear some USB data (i.e. pump cycles, driver cycles, etc.)  It is recommended that a full USB download be completed before upgrading software.

Software Upgrade Token 18D389 Series F

  • System: 18D388f.gti (Software Link) version 1.03.003
  • Advanced Display (ADM): 18D382 version 1.03.002
  • USB Configuration: 18D385 version 1.01.001
  • Motor Control Module (MCM): 18D386 version 1.02.003
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Pressure limit set to alarm at 7000psi instead of 7500psi. Because the last revision corrected the pressure reading, it was found once a transducer was disconnected the software did not correctly update the case of an alarm throwing because of a transducer not being installed. To remedy this, the limit was changed from 7500psi to 7000psi so the ADM will throw the alarm correctly.

Software Upgrade Token 18D389 Series E

  • System: 18D388 version 1.03.002
  • Advanced Display (ADM): 18D382 version 1.03.002
  • USB Configuration: 18D385 version 1.01.001
  • Motor Control Module (MCM): 18D386 version 1.02.002
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Fixed pressure reading for standard and flush-mount transducers.

Software Upgrade Token 18D389 Sreies D

  • System: 18D388 version 1.03.001
  • Advanced Display (ADM): 18D382 version 1.03.001
  • USB Configuration: 18D385 version 1.01.001
  • Motor Control Module (MCM): 18D386 version 1.02.001
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Fixed issue with screen updates
  • The data exchange was limited to a minimal interval of 50ms between each element request.

Software Upgrade Token 18D389 Series C

  • System 18D388c version 1.02.001
  • Advanced Display (ADM): 18D382 version 1.02.001
  • USB Configuration: 18D385 version 1.01.001
  • Motor Control Module (MCM): 18D386 version 1.01.002
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Added the time and date to the map (P/N: 18D562).
  • Updated the Pumps start/stop button to clear up customer confusion.
  • The drum height drop down was turned into a settable drum height.

Software Upgrade Token 18D389 Series B

  • System: 18D388b.gti version 1.01.001
  • Advanced Display (ADM): 18D382 version 1.01.001
  • USB Configuration: 18D385 version 1.01.001
  • Motor Control Module (MCM): 18D386 version 1.01.001
  • Communications Gateway Module (CGM): 17P796 version 3.01.004

Change History

  • Initial Release