EFR Software Change History

The Version History of EFR Software is listed below. The software currently installed on an EFR system can be found by navigating to Advanced Setup Screen two. Details on this screen can be found in EFR instruction manual (P/N: 3A6165). If upgrade to newer software version is desired, order the appropriate “Software Upgrade Token” as listed below.

All EFR systems should match one of the system versions under “EFR Software Version/Change History.”

 

EFR Fieldbus Files are located through the links below:

Software Upgrade Token 17Y11 Series ZAG

  • System 17V658zag.gti (Software Link) version 1.12.004
  • Advanced Display (ADM):  17V652 Version 1.08.004
  • USB Configuration:  17V764 Version 1.10.004
  • Motor Control Module (3MCP):  17V655 version 1.14.004
  • Inlet Fluid Control Module (FCM3):  17V654 version 1.03.005
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001
  • Voltex Dynamic Mix Valve (FCM3): 18C787 version 1.03.004
  • Tank Stand(s) Monitor/Control Module (FCM3): 16A206 version 1.05.012

Change History

  • Made shot log more accurate. Resolved issue where run screen dispense amount did not match the amount recorded in the USB shot log.
  • Fixed issue where pumps where short stroking when in recirculation and purging modes

Software Upgrade Token 17Y711 Series ZAF.

  • System 17V658 version 1.10.002
  • Advanced Display (ADM):  17V652 Version 1.07.007
  • USB Configuration:  17V764 Version 1.06.018
  • Motor Control Module (3MCP):  17V655 version 1.11.010
  • Inlet Fluid Control Module (FCM3):  17V654 version 1.03.004
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001
  • Voltex Dynamic Mix Valve (FCM3): 18C787 version 1.03.004
  • Tank Stand(s) Monitor/Control Module (FCM3): 16A206 version 1.05.012

Change History

  • IMPORTANT: This token will deleted and reset the sequence definitions information, it is recommend taking picture of desired information before updating, as the information will need to be re-entered after updating.
  • Added dispensing motor and valve delays when Voltex is not connected.
  • Added tip valve control for Voltex.

Software Upgrade Token 17Y711 Series AE.

 

  • System 17V658ae Version 1.09.010
  • Advanced Display (ADM):  17V652 Version 1.06.010
  • USB Configuration:  17V764 Version 1.06.018
  • Motor Control Module (3MCP):  17V655 version 1.10.010
  • Inlet Fluid Control Module (FCM3):  17V654 version 1.03.004
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001
  • Voltex Dynamic Mix Valve (FCM3): 18C787 version 1.03.003
  • Tank Stand(s) Monitor/Control Module (FCM3): 16A206 version 1.05.012

Change History

  • Added a feature to the ADM softkeys. So that, the Voltex’s motor and or air nucleation can be disabled while dispensing.
  • Also fixed bug, that did not clear out the maintenance counters, when the advisory limit was turn off.

Software Upgrade Token 17Y711 Series AD.

 

  • System 17V658ad Version 1.09.006
  • Advanced Display (ADM):  17V652 Version 1.06.005
  • USB Configuration:  17V764 Version 1.06.017
  • Motor Control Module (3MCP):  17V655 version 1.10.006
  • Inlet Fluid Control Module (FCM3):  17V654 version 1.03.004
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001
  • Voltex Dynamic Mix Valve (FCM3): 18C787 version 1.03.002
  • Tank Stand(s) Monitor/Control Module (FCM3): 16A206 version 1.05.011

Change History

  • Added the manual and timer recirculation features into the EFR.
  • Removed errors P3FA and P3FB.
  • Fixed problem where the inlet pressure kit number was not display correctly on the ADM.

Software Upgrade Token 17Y711 Series AC.

 

  • System 17V658ac Version 1.09.002
  • Advanced Display (ADM):  17V652 Version 1.06.002
  • USB Configuration:  17V764 Version 1.06.0017
  • Motor Control Module (3MCP):  17V655 version 1.10.003
  • Inlet Fluid Control Module (FCM3):  17V654 version 1.03.002
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001
  • Voltex Dynamic Mix Valve (FCM3): 18C787 version 1.03.002
  • Tank Stand(s) Monitor/Control Module (FCM3): 16A206 version 1.05.011

Change History

  • Fixed issues with the CAN network.
  • Removed an error.
  • Re-ordered the Voltex communication structure. IMPORTANT: Will cause the Voltex default to product setup values. It is recommend that setup variables are saved before updating.  
  • Added the inlet pressure kit 25U084 into code.

Software Upgrade Token 17Y711 Series AB.

 

  • System 17V658ab Version 1.07.004
  • Advanced Display (ADM):  17V652 Version 1.05.007
  • USB Configuration:  17V764 Version 1.06.0017
  • Motor Control Module (3MCP):  17V655 version 1.08.08
  • Inlet Fluid Control Module (FCM3):  17V654 version 1.02.002
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001
  • Voltex Dynamic Mix Valve (FCM3): 18C787 version 1.01.011
  • Tank Stand(s) Monitor/Control Module (FCM3): 16A206 version 1.05.008

Change History

  • Fixed communication problems with the Voltex Dynamic Mix Valve that would cause the network to reset.

Software Upgrade Token 17Y711 Series AA.

 

  • Advanced Display (ADM):  17V652 Version 1.05.006
  • USB Configuration:  17V764 Version 1.06.0017
  • Motor Control Module (3MCP):  17V655 version 1.08.06
  • Inlet Fluid Control Module (FCM3):  17V654 version 1.02.002
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001
  • Voltex Dynamic Mix Valve (FCM3): 18C787 version 1.01.011
  • Tank Stand(s) Monitor/Control Module (FCM3): 16A206 version 1.05.008

Change History

  • Integrated Tank Stand(s) software into the EFR and the EFR 19A796 CGM map.

Software Upgrade Token 17Y711 Series Z.

 

  • Advanced Display (ADM):  17V652 Version 1.04.007
  • USB Configuration:  17V764 Version 1.06.004
  • Motor Control Module (3MCP):  17V655 version 1.07.014
  • Inlet Fluid Control Module (FCM3):  17V654 version 1.02.002
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001
  • Voltex Dynamic Mix Valve: 18C787 version 1.01.011

Change History

  • Integrated the new Voltex Dynamic Mix Valve into the EFR and the EFR 19A796 CGM map.

Software Upgrade Token 17Y711 Series Y.

 

  • System 17V658y Version 1.05.006 
  • Advanced Display (ADM):  17V652 Version 1.02.067
  • USB Configuration:  17V764 Version 1.05.001
  • Motor Control Module (3MCP):  17V655 version 1.06.008
  • Fluid Control Module (FCM3):  17V654 version 1.01.006
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001

Change History

  • Fixed issues with the shot log screen on the ADM, reporting the correct last log for a dispense on the screen.  More information about a particular dispense is available with a USB stick download.
  • Fixed an issue where the material counters would roll-over when in weight mode after a long dispense.
  • Added logic to the material reported on screen, the shot log screen and the CGM/PLC interface to take into account the shot offset (or delta) amount entered for the dispense.
  • Fixed an EE2 issue with the 3HP driver.

Software Upgrade Token 17Y711 Series W.

 

  • System 17V658w 1.05.004
  • Advanced Display (ADM):  17V652 Version 1.02.062
  • USB Configuration:  17V764 Version 1.05.001
  • Motor Control Module (3MCP):  17V655 version 1.05.011
  • Fluid Control Module (FCM3):  17V654 version 1.01.006
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001

Change History

  • Re-wrote the EE2 access logic on the 3MCP module, to prevent a situation where the module thinks it is a new module at bootup, and configures the PCB to its default configuration, causing the re-execution of the learn mode process.
  • Added logic to support the insertion of a new 25T590 blue token assembly.  If the new token is inserted into the ADM, the logic will disable the generation of P4FX errors which warn the user that the feed pressure into the product Z pump inlets may be excessive. 

Software Upgrade Token 17Y711 Series V.

 

  • System 17V658s 1.05.001
  • Advanced Display (ADM):  17V652 Version 1.02.062
  • USB Configuration:  17V764 Version 1.05.001
  • Motor Control Module (3MCP):  17V655 version 1.05.003
  • Fluid Control Module (FCM3):  17V654 version 1.01.006
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001

Change History

  • Modified logic on 3MCP PCB to NOT save to EE2 memory operator mode type dispense flow rate changes originating from the CGM interface.  This modification will prevent excessive wear on the corresponding memory locations, if the user is changing the flow rate “on the fly” excessively.
  • Fixed an issue on the ADM module, which degraded communication between the ADM module and system information provided by the 3MCP module.

Software Upgrade Token 17Y711 Series U.

 

  • Advanced Display (ADM):  17V652 Version 1.02.060
  • USB Configuration:  17V764 Version 1.05.001
  • Motor Control Module (3MCP):  17V655 version 1.04.053
  • Fluid Control Module (FCM3):  17V654 version 1.01.006
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001

Change History

  • Enhanced the USB Dispense/ Sequence logging function significantly!  The sequence logs now output a log entry (row) at dispense start, stop and every 2 seconds of a dispense or sequence step, making the log file more reflective of real time operation of the machine.  Previously, a log entry would only occur at the end of an entire sequence.  Furthermore, each log entry contains more information (columns) compared the previous version.  The shot log screen on the ADM has also been updated accordingly.
  • Improved the communication between electronic nodes (ADM, 3MCP, ..) within the product, which was causing problems, when trying to control the machine from the ADM.  Operations like changing a sequence number will operate more reliably than before.
  • Added an Advanced #3 setup screen, to allow the user to enter material labels for the machine, which are now viewable on the main screen. 
  • The new Advanced #3 setup screen also provides capability to configure the ratio set point to display in blue/red to 1, or red/blue to 1 formats.  The new configurable machine ratio is now viewable on the shot/ sequence USB logs as a column element.

Software Upgrade token 17Y711 Series T.

 

  • Advanced Display (ADM):  17V652 Version 1.02.035
  • USB Configuration:  17V764 Version 1.03.010
  • Motor Control Module (3MCP):  17V655 version 1.04.038
  • Fluid Control Module (FCM3):  17V654 version 1.01.006
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001

Change History

  • Fixed an issue where an operator mode type dispense could not be cancelled from the foot switch, if the switch was activated extremely fast.
  • Fixed an issue where the dispensed amount in the USB log was not outputting correct data consistently.  
  • Increased the frequency of several data elements reported to the PLC/ CGM and USB interfaces to make it more “real time”, rather than reporting only at the end of a dispense.
  • Added an ADM Lockout feature, which can be requested by the PLC/ CGM interface.
  • Added a Dispense duration feature, and fixed the dispense amount information reported to the PLC/ CGM interface.
  • Added a PLC Monitor only feature, available on the PLC/ CGM interface.
  • Added a Heart-beat feature from the PLC/ CGM interface.  Fixed the generation of the “CCCC” advisory, which had the incorrect string association (“Field bus/ PLC Offline”).  If generated, the logic will turn OFF the new “ADM Lockout” feature if active.

Software Upgrade Token 17Y711 Series S.

 

  • System 17V658s 1.04.007
  • Advanced Display (ADM):  17V652 Version 1.02.031
  • USB Configuration:  17V764 Version 1.03.010
  • Motor Control Module (3MCP):  17V655 version 1.04.023
  • Fluid Control Module (FCM3):  17V654 version 1.01.006
  • Communication Gateway (CGM):  17P796 version 3.01.004
  • Wireless CGM Module (WPAN):  17T720 version 0.08.001

Change History

  • Fixed an issue where the incorrect pressure unit of measure label was displayed on the System #3 setup screen.
  • Fixed an issue where the pressures displayed on the ADM did not match reality.
  • Fixed a minimum and maximum pressure user entry issue on the System #3 setup screen, if the FCM3 was offline.
  • Increased the pressure resolution to 0.1 bar units when selected, on both the pressures displayed and when entering pressure settings.
  • Added the capability for the user to Start and Cancel an operator mode type dispense from the ADM, rather than requiring the user to connect a footswitch or CGM to trigger a dispense. 
  • Added logic to the ADM to prevent the user from “Pausing” and operator mode type dispense, and from changing the sequence number if the current sequence is NOT “Stopped”.  Activating those controls in those conditions can cause problems.
  • Fixed issues in the “Total Sequence Amount Requested” and the “Total Sequence Amount Dispensed” fields reported on the CGM interface to the PLC.  The sequence amount requested field is now updated at the start of the 1st step in a sequence, and the Amount Dispensed field is updated in real time format.

Software Upgrade Token 17Y711 Series Q.

 

  • System 17V658 1.04.002
  • Advanced Display (ADM):  17V652 Version 1.02.021
  • USB Configuration: 17V764 Version 1.03.010
  • Motor Control Module (3MCP):  17V655 version 1.04.008

** The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module (FCM3):  17V654 version 1.01.006
  • Communication Gateway (CGM):  17P796 version 3.01.004

Change History

  • Fixed issue where “—“ would be displayed on ADM if pressure(s) monitored were less than about 7 bar (100 PSI).
  • Added logic to enable a user to cancel an active dispense (or the current step in a sequence) by tapping the foot switch input.
  • Added Pump and Dispense valve cycle limit entries to the Setup Maintenance #1 screen, to enable the user to generate an advisory if a pump or the dispense valve cycles above the limit entered.

Software Upgrade Token: 17Y711 Series P.

 

  • System 17V658 version 1.04.001
  • Advanced Display: 17V652 Version 1.02.001
  • USB Configuration: 17V764 Version 1.03.009
  • Motor Control Module: 17V655 Version 1.04.002

**The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module: 17V654 Version 1.01.006
  • Gateway: 3.01.004

Change History

  • Fixed issues with the writing to the EEPROM chip on the MCM.
  • Removed the indeterminate delay when laying beads.

Software Upgrade Token: 17Y711 Series M.

 

  • System: 17V658 (Software Link) Version 1.02.019
  • Advanced Display: 17V652 Version 1.01.019
  • USB Configuration: 17V764 Version 1.03.009

**The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module: 17V654 Version 1.01.006
  • Gateway: 17P796 Version 3.01.004

Change History

  • CGM interface modified to report the alarm being shown by the ADM pop-up screen.  If the CGM acknowledges the code, it clears the pop-up on the ADM as well.
  • Corrected a condition where the sequence information would not be properly retrieved when requested from the CGM.
  • Removed unused IO from the Gateway Interface.
  • Corrected a condition where pressures would not log properly on the first shot after a power cycle.
  • Added a user configurable pressure window for inlet and outlet pressures.  This is monitored during EFR dispensing.  The user can specify Min/Max limits for A & B individually and how to classify the alerts for each limit pair (None, Deviation, Alarm).
  • Removed Leak Detection.

Software Upgrade Token: 17Y711 Series L.

 

  • System: 17V658 Version 1.02.010
  • Advanced Display: 17V652 Version 1.01.008
  • USB Configuration: 17V764 Version 1.03.007
  • Motor Control Module: 17V655 Version 1.02.010

**The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module: 17V654 Version 1.01.002
  • Gateway: 3.01.004

Change History

  • Fixed bugs that where found in the algorithm that is used to detect high inlet pressure.

 

Software Upgrade Token: 17Y711 Series K.

 

  • Advanced Display: 17V652 Version 1.01.008
  • USB Configuration: 17V764 Version 1.03.007
  • Motor Control Module: 17V655 Version 1.02.009

 

**The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module: 17V654 Version 1.01.002
  • Gateway: 3.01.004

Change History

  • Fixed bugs that were found in the smart change algorithm. 
  • Change pressure display on the ADM so that if below a certain threshold, it will not display the pressure.

Software Upgrade Token: 17Y711 Series J.

 

  • Advanced Display: 17V652 Version 1.01.008
  • USB Configuration: 17V764 Version 1.03.007
  • Motor Control Module: 17V655 Version 1.02.007

**The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module: 17V654 Version 1.01.002
  • Gateway: 3.01.004

Change History

  • Line voltage on the Diagnostics screen was changed from DC Bus Voltage to actual AC line voltage see by the EFR.
  • High Inlet Pressure alarm is only trigger while a sequence is dispensing and after the inlet pressure has been higher then the 2/3 of outlet pressure for 800ms.
  • CGM Acknowledgement numbering overlapped, starting from VN1X: Low Voltage Alarm the error values are now plus one. Refer to manual P/N 3A6338 revision B for correct error values.

Software Upgrade Token: 17Y711 Series H.

 

  • Advanced Display: 17V652 Version 1.01.008
  • USB Configuration: 17V764 Version 1.03.007
  • Motor Control Module: 17V655 Version 1.02.03

**The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module: 17V654 Version 1.01.002
  • Gateway: 3.01.004

Change History

  • Updated software to work with the EFR CGM Map P/N 19A796.

 

Software Upgrade Token: 17Y711 Series G.

 

  • Advanced Display: 17V652 Version 1.01.008
  • USB Configuration: 17V764 Version 1.03.007
  • Motor Control Module: 17V655 Version 1.01.023

**The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module: 17V654 Version 1.01.002
  • Gateway: 3.01.004

Change History

  • Fixed bugs that were found in sequence repeat.

 

Software Upgrade Token: 17Y711 Series F.

 

  • Advanced Display: 17V652 Version 1.01.008
  • USB Configuration: 17V764 Version 1.03.007
  • Motor Control Module: 17V655 Version 1.01.022

**The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module: 17V654 Version 1.01.002
  • Gateway: 3.01.004

Change History

  • Fixed bugs that were found in the I/O integration.

 

Software Upgrade Token: 17Y711 Series E.

 

  • Advanced Display: 17V652 Version 1.01.008
  • USB Configuration: 17V764 Version 1.03.007
  • Motor Control Module: 17V655 Version 1.01.021

**The following components will only display if connected, as they are add on items to the system**

  • Fluid Control Module: 17V654 Version 1.01.002
  • Gateway: 3.01.004

Change History

  • Initial Release.